lis3dh/example

lis3dh/example

file: simple.c

Basic example of how to use this device

FIFO

Instead of polling for every single [x y z] set, a FIFO with programmable capacity ("watermark") can be used, and then dumped into memory once full.

All FIFO readings use 10-bit resolution regardless of the mode set in cfg.mode.

The watermark level can be adjusted to a value [1-32] (0 disables FIFO) by modifying the cfg.fifo.size property before calling lis3dh_configure().

The FIFO "engine" samples/appends another set of [x y z] values at 1/ODR. The maximum ODR supported by the FIFO "engine" is 200 Hz.

files in fifo/ dir

FIFO mode	symbol	description
Bypass	LIS3DH_FIFO_MODE_BYPASS	FIFO is inoperational
FIFO	LIS3DH_FIFO_MODE_FIFO	FIFO can be read/emptied at any time but once overrun has to be reset. See files: fifo-int-ovrn.c, fifo-int-wtm.c, fifo.c
Stream	LIS3DH_FIFO_MODE_STREAM	FIFO continously writes new data at 1/ODR and will overwrite old data until it is read/emptied. See files: stream-int-ovrn.c, stream-int-wtm.c, stream.c
Stream_to_FIFO	LIS3DH_FIFO_STREAM_TO_FIFO	FIFO behaves like Stream mode until a set interrupt is activated, then changes to a mode FIFO.

Note: FIFO will not trigger a watermark interrupt (pin1.wtm) if the FIFO size is default (32; maximum size). To use the watermark interrupt, the FIFO size has to be between [1-31]. An overrun interrupt (pin1.overrun) will always trigger when the FIFO is full, regardless of programmed capacity.

Note: to sample data faster than 200 Hz, it is necessary to use the regular data polling functionality using lis3dh_read() with the appropriate configuration. See files simple.c and fast.c for examples.

file: single-click.c

Set up single-click detection (no latching interrupt possible)

file: double-click.c

Set up double-click detection (no latching interrupt possible)

file: adc.c

Enable and read built-in ADCs.

• Input range: 800 mV to 1600 mV
• Resolution: 8-bit in LP mode, 10-bit in normal and in HR mode.
• Sampling frequency: same as ODR

file: temp.c

Enable and read built-in temperature sensor

• Operating range: -40 to 85°C
• Step size: ±1°C

Inertial interrupts

There are two interrupt registers, int1 and int2 that can be configured for inertial interrupts. The config structs are identical and contain the fields: zh, zl, yh, yl, xh, xl, and more. zh stands for Z_axis_high and zl stands for Z_axis_low. If both are enabled, the device will generate an interrupt upon Z-axis acceleration exceeding threshold, or upon Z-axis acceleration reading at or below -threshold (in OR mode. Not possible in AND mode).

aoi	en_6d	interrupt mode
0	0	OR combination
0	1	6d MOVEMENT recognition
1	0	AND combination
1	1	6d POSITION recognition

OR combination

An interrupt is generated when at least one of the configured axes is at or above the threshold level.

6D MOVEMENT recognition

An interrupt is generated when the device moves from a direction (known or unknown) to a different known direction. The interrupt is only active for 1/ODR.

AND combination

An interrupt is generated when all of the configures axes are at or above the threshold level.

6D POSITION recognition

An interrupt is generated when the device is "stable" in a known direction. The interrupt is active as long as the direction is maintained.

file: inertial-wakeup.c

Inertial interrupt example in OR mode (easily changed to AND mode) with configurable axes, threshold and minimum acceleration duration.

file: free-fall.c

Inertial interrupt example activating upon free-fall. It works by using an AND mode interrupt of all the negative axes and comparing them to a threshold value (in the case of negative axis the threshold is multiplied by -1), recommended to be at 350mg (for >30 ms) and activating when the experienced negative acceleration is greater (abs. sense) than the negative threshold.

file: 6d-movement.c

Inertial interrupt example, generates an interrupt when some acceleration, threshold is experienced on any configured axis for duration time. Supposedly the device knows what a "known" direction is.

file: 6d-position.c

Inertial interrupt example, the interrupt line is kept active so long as the device is stable (ie acceleration on configured axes does not exceed threshold for duration time).

---

4D detection

4D detection is a subset of 6D detection meant for detecting portrait/landscape screen rotations on mobile phones, etc. It functionally works the same as the 6D modes, except that detection along the Z-axis is disabled.

file: 4d-movement.c

Inertial interrupt example, generates an interrupt when some acceleration, threshold is experienced on any configured axis for duration time. Supposedly the device knows what a "known" direction is.

file: 4d-position.c

Inertial interrupt example, the interrupt line is kept active so long as the device is stable (ie acceleration on configured axes does not exceed threshold for duration time).