2023-09-17 20:31:02 +00:00
|
|
|
# bme680
|
2023-09-18 03:54:42 +00:00
|
|
|
|
2023-11-06 15:08:28 +00:00
|
|
|
Example implementation of BME680 software. The I2C/SPI drivers are meant to run on a Raspberry Pi 4 but you can figure out how to port it.
|
2023-11-04 17:26:23 +00:00
|
|
|
|
2023-09-18 03:54:42 +00:00
|
|
|
|
2023-11-06 15:08:28 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
Connecting the purple BME680 module board to SPI:
|
|
|
|
|
|
|
|
|
|
| SPI func | BME680 Pin | Raspberry Pi Pin |
|
|
|
|
|
| -------- | ---------- | ---------------- |
|
|
|
|
|
| MISO | "SDO" | GPIO 9 (Pin 21) |
|
|
|
|
|
| MOSI | "SDA" | GPIO 10 (Pin 19) |
|
|
|
|
|
| SCLK | "SCL" | GPIO 11 (Pin 23) |
|
|
|
|
|
| CS | "CS" | GPIO 8 (Pin 24) |
|
|
|
|
|
|
|
|
|
|
## spi demo
|
2023-09-18 03:54:42 +00:00
|
|
|
```
|
|
|
|
|
par_t1: 26203
|
|
|
|
|
par_t2: 26519
|
|
|
|
|
par_t3: 3
|
|
|
|
|
par_p1: 35008
|
2023-09-18 15:32:27 +00:00
|
|
|
par_p2: -10284
|
2023-09-18 03:54:42 +00:00
|
|
|
par_p3: 88
|
|
|
|
|
par_p4: 9692
|
2023-09-18 15:32:27 +00:00
|
|
|
par_p5: -202
|
2023-09-18 03:54:42 +00:00
|
|
|
par_p6: 30
|
|
|
|
|
par_p7: 24
|
2023-11-04 17:26:23 +00:00
|
|
|
par_p8: -4
|
2023-09-18 15:32:27 +00:00
|
|
|
par_p9: -3469
|
2023-09-18 03:54:42 +00:00
|
|
|
par_p10: 30
|
|
|
|
|
par_h1: 794
|
2023-09-18 15:32:27 +00:00
|
|
|
par_h2: 1007
|
2023-09-18 03:54:42 +00:00
|
|
|
par_h3: 0
|
|
|
|
|
par_h4: 45
|
|
|
|
|
par_h5: 20
|
|
|
|
|
par_h6: 120
|
2023-09-18 15:32:27 +00:00
|
|
|
par_h7: -100
|
2023-11-05 02:58:23 +00:00
|
|
|
par_g1: 208
|
|
|
|
|
par_g2: 59781
|
|
|
|
|
par_g3: 18
|
|
|
|
|
range_switching_error: 19
|
|
|
|
|
res_heat_range: 1
|
|
|
|
|
res_heat_val: 46
|
2023-11-04 17:26:23 +00:00
|
|
|
float mode
|
2023-11-06 15:08:28 +00:00
|
|
|
tfine: 104478.758986
|
|
|
|
|
temp: 20.406008 degC
|
|
|
|
|
press: 99649.423644 Pa
|
|
|
|
|
humidity: 65.368724 % RH
|
|
|
|
|
gas resistance: 10989.279979 Ohm
|
|
|
|
|
== for heater target=300.0 and ambient temp=19.0 (degC)
|
2023-09-18 03:54:42 +00:00
|
|
|
```
|
2023-11-06 15:08:28 +00:00
|
|
|
|
|
|
|
|
## i2c demo
|
|
|
|
|
```
|
|
|
|
|
par_t1: 26125
|
|
|
|
|
par_t2: 26370
|
|
|
|
|
par_t3: 3
|
|
|
|
|
par_p1: 36262
|
|
|
|
|
par_p2: -10371
|
|
|
|
|
par_p3: 88
|
|
|
|
|
par_p4: 6713
|
|
|
|
|
par_p5: -103
|
|
|
|
|
par_p6: 30
|
|
|
|
|
par_p7: 31
|
|
|
|
|
par_p8: -251
|
|
|
|
|
par_p9: -3158
|
|
|
|
|
par_p10: 30
|
|
|
|
|
par_h1: 776
|
|
|
|
|
par_h2: 1010
|
|
|
|
|
par_h3: 0
|
|
|
|
|
par_h4: 45
|
|
|
|
|
par_h5: 20
|
|
|
|
|
par_h6: 120
|
|
|
|
|
par_h7: -100
|
|
|
|
|
par_g1: 183
|
|
|
|
|
par_g2: 59281
|
|
|
|
|
par_g3: 18
|
|
|
|
|
range_switching_error: 19
|
|
|
|
|
res_heat_range: 1
|
|
|
|
|
res_heat_val: 39
|
|
|
|
|
float mode
|
|
|
|
|
tfine: 102706.944886
|
|
|
|
|
temp: 20.059950 degC
|
|
|
|
|
press: 99783.521673 Pa
|
|
|
|
|
humidity: 63.931961 % RH
|
|
|
|
|
gas resistance: 12028.902897 Ohm
|
|
|
|
|
== for heater target=300.0 and ambient temp=19.0 (degC)
|
|
|
|
|
```
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: Two different BME680 devices, one on each type of bus. Low air pressure due to storm not bad sensor.
|
